Packet Tracer - Skills Integration Challenge Topology
Addressing Table IPv4 Address Device
Subnet Mask
Interface IPv6 Address/Prefix S0/0/0
172.31.6.1
255.255.255.252
S0/0/1
10.10.8.1
255.255.255.252
S0/1/0
209.165.200.226
255.255.255.224
R1
S0/0/0
172.31.6.2
255.255.255.252
R2
S0/0/1
10.10.8.2
255.255.255.252
S0/0/0
2001:DB8:A001:6::1/64
S0/0/1
2001:DB8:A001:7::1/64
S0/1/0
2001:DB8:CAFE:1::2/64
R3
S0/0/0
2001:DB8:A001:7::2/64
R4
S0/0/1
2001:DB8:A001:6::2/64
IPv4-Edge
IPv6-Edge
Scenario In this activity, you are tasked with implementing EIGRP for IPv4 and IPv6 on two separate networks. Your task includes enabling EIGRP, assigning router-IDs, changing the hello timers, configuring EIGRP summary routes and limiting EIGRP advertisements.
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Page 1 of 3
Packet Tracer - Skills Integration Challenge
Requirements EIGRP for IPv4 
Implement EIGRP on IPv4 enabled routers using Autonomous System 1. -
Use the classful network address for the loopback interfaces.
-
Use the wildcard mask to advertise the /30 networks between R1, R2 and IPv4-Edge.
-
Use the default method to only allow EIGRP updates out the active EIGRP serial interfaces.
-
Advertisements should not be summarized.

Configure a directly attached default route on IPv4-Edge and propagate it in EIGRP updates.

Configure the serial interfaces between R1, R2 and IPv4-Edge to send hellos every 10 seconds.

On R1 and R2, configure an EIGRP summary route for the loopback networks. R1 Loopback Networks
R2 Loopback Networks
172.31.0.0/25
10.10.0.0/24
172.31.0.128/25
10.10.1.0/24
172.31.1.0/25
10.10.2.0/23
172.31.1.128/25
10.10.4.0/22
Summary:
Summary:

R1 and R2 should only have four EIGRP routes in the routing table, one of which is the default route (D*EX). IPv4-Edge should only have two EIGRP routes in the routing table.

Verify R1 and R2 can ping the IPv4 Server. IPv4 Server should also be able to ping every loopback address on R1 and R2.
EIGRP for IPv6 
Implement EIGRP on IPv6 enabled routers using Autonomous System 1. -
Assign IPv6-Edge with the router-ID of 1.1.1.1
-
Assign R3 with the router-ID of 3.3.3.3
-
Assign R4 with the router-ID of 4.4.4.4

Configure a directly attached default route on IPv6-Edge and propagate it in EIGRP updates.

On R3 and R4, configure an EIGRP summary route for the loopback networks. R3 Loopback Networks

R4 Loopback Networks
2001:DB8:1:1:A000::1/72
2001:DB8:1:1:BB80::1/76
2001:DB8:1:1:A100::1/72
2001:DB8:1:1:BB90::1/76
2001:DB8:1:1:A200::1/72
2001:DB8:1:1:BBA0::1/76
2001:DB8:1:1:A300::1/72
2001:DB8:1:1:BBB0::1/76
Summary:
Summary:
R3 and R4 should only have four EIGRP routes in the routing table, counting the default external route. IPv6-Edge should only have two EIGRP routes in the routing table.
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Page 2 of 3
Packet Tracer - Skills Integration Challenge 
Verify R3 and R4 can ping the IPv6 Server. IPv6 Server should also be able to ping every loopback address on R3 and R4.
Suggested Scoring Rubric Note: Packet Tracer does not currently grade EIGRP for IPv6 summary routes. Therefore, part of your grade depends on routing table verification by your instructor.
Scored Work
Possible Points
IPv6-Edge Routing Table
10
Packet Tracer Score
90
Total Score
100
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Earned Points
Page 3 of 3